How to Plasti Dip Emblems: Step by Step Guide

Step One: Masking

Ensure that your vehicle is clean and dry, parked in the shade so that it is cool to the touch. Mask the area around the emblem(s) that you are changing the colour of, to prevent over spray. Make sure to leave approximately one inch of exposed paint around the area to help with later steps.

Step Two: Coating

For each emblem, four to five light coats is recommended. I started with one coat on a downwards angle, and then let dry for fifteen minutes. I did an upward angle coat, and waited another fifteen minutes. A right and then left angle coat came next, both with fifteen minute wait times again. I finished with a head on coat, with no angle to ensure properly full and even coverage.

Step Three: Drying Time

After the final coat, wait approximately thirty minutes for the plasti dip to be dry to the touch. The time will vary based on number and thickness of coats, as well as environmental factors such as temperature and humidity.

Step Four: Remove Masking

After ensuring that the surface area is dry to the touch, remove your surrounding masking tape. Try not to peel the Plasti Dip too much, but don’t worry if you do a little bit.

Step Five: Remove Excess

Using the inch of extra area that was left around the area, start by peeling at the edges where the masking tape was while keeping your angle of removal closely parallel to the body. To remove small pieces inside of closed loops such as my “O” emblem, I used a wooden toothpick. Never touch the paint with the wood, only the Plasti Dip. Take your time and have patience, a break may be needed in between.

Step Six: Finish

Ensure that their is no residual adhesive left from your painter’s tape. If there is any over mist from the Plasti Dip, it can easily be wiped off with a clean microfiber cloth. Be careful not to touch the emblem(s) as much as possible, as it may take a few hours to fully cure. After that you are done, and can enjoy your newly enhanced logos!

Sponsored Posts

Comments

Michael R. T. Jensen

Wogmidget

08/29/2017 - 17:20 |
0 | 0

Nice work mate, that’s come up really nicely.

08/29/2017 - 21:14 |
0 | 0
Michael R. T. Jensen

Ethan Riley

08/29/2017 - 17:21 |
0 | 0

That looks dang good, dude.

08/29/2017 - 18:28 |
1 | 0
Michael R. T. Jensen

Thomas Beck

08/29/2017 - 17:24 |
0 | 0

Wow!
Turned out much better then expected!
Glad you used matt black and not gloss black.

08/29/2017 - 17:29 |
0 | 0
Anonymous

Thug lyfe intensifies

08/29/2017 - 17:32 |
1 | 0
Michael R. T. Jensen

In reply to by Anonymous (not verified)

#ThugLyfe intensifies more…

08/29/2017 - 17:36 |
1 | 0
Audilover

Looks good.

08/29/2017 - 17:33 |
1 | 0
Michael R. T. Jensen

In reply to by Audilover

Thanks!

08/29/2017 - 17:34 |
0 | 0
Sarove (Crown Vic)

Looks better than I anticipated. Nice guide as well!

08/29/2017 - 18:21 |
1 | 0

Thanks ×2!

08/29/2017 - 18:21 |
0 | 0
ThatFordGuy

Dude, that’s so sick! I love it!

08/29/2017 - 18:24 |
1 | 0

Thanks!

08/29/2017 - 18:25 |
1 | 0
Metrickzcz (Prelude Squad)

Step 1: Make sure you are sponsored by Danone

08/29/2017 - 18:30 |
1 | 0

Step 2: Get turned down by Danone

08/29/2017 - 18:31 |
0 | 0
TheCarGuy 2

You have the potental to be a car diy youtuber haha this is awesome!

08/29/2017 - 19:11 |
1 | 0

LoL, if only I actually made videos.

08/29/2017 - 19:12 |
1 | 0
LittleFun

Honestly 3 dollars for a shampoo is overpriced

08/29/2017 - 21:44 |
1 | 0
Michael R. T. Jensen

In reply to by LittleFun

Maybe it smells really good?

08/29/2017 - 21:49 |
0 | 0